Build a Raised Cedar Garden Planter Box
Woodworking

Build a Raised Cedar Garden Planter Box

Build a beautiful 4x4 foot raised garden bed using rot-resistant cedar boards. This beginner-friendly woodworking project takes about 2-3 hours and creates a sturdy planter perfect for vegetables, herbs, or flowers. No advanced tools required—just basic carpentry skills.

AM
Alex M.· Nov 16, 2026
0 of 12 done

Plan your planter dimensions and location

Decide where your planter will go and confirm it gets adequate sunlight (6-8 hours for vegetables). Mark out a 4x4 foot area and ensure the ground is relatively level. This project creates a box that's 4 feet long, 4 feet wide, and 16 inches tall.

measuring tapegarden location

Cut the cedar boards to length

Using your circular saw or miter saw, cut the 1x8 cedar boards into eight pieces at 48 inches long (for the long sides) and eight pieces at 46.5 inches long (for the short sides). The slight difference accounts for board thickness so corners fit flush. Sand any rough edges lightly.

circular sawcedar boardsmeasuring tapepencilsandpaper

Prepare your corner posts

Cut four pieces of 2x2 cedar at 16 inches each to serve as internal corner posts. These will provide structure and make assembly much easier. Set these aside—you'll attach them in the next step.

2x2 cedar postscircular sawmeasuring tape

Assemble the first layer frame

Lay out two 48-inch boards (long sides) and two 46.5-inch boards (short sides) on a flat surface to form a rectangle. Position a 16-inch corner post at each inside corner, flush with the top edge. The short boards sit between the long boards at the ends.

48-inch cedar boards46.5-inch cedar boardscorner posts

Secure the first layer with screws

Using your drill, drive two 2.5-inch exterior screws through each board into the corner post at each corner. Pre-drill small pilot holes first to prevent the cedar from splitting. Make sure everything is square before fully tightening. You should now have a sturdy rectangular frame.

cordless drill2.5-inch exterior screwscorner postssquare

Add the second layer of boards

Stack another set of four boards (two long, two short) directly on top of the first layer, staggering the seams so they don't line up with the layer below. This adds strength. Align the edges carefully.

48-inch cedar boards46.5-inch cedar boards

Attach the second layer

Drive 2.5-inch screws through the second layer into the corner posts, using two screws per board end just like before. Also drive 1-2 screws through the second layer into the first layer along the long sides (not at corners) to bond the layers together.

cordless drill2.5-inch exterior screws

Install the third and fourth layers

Repeat the stacking process for layers three and four, continuing to stagger seams and securing each layer with screws into the corner posts and into the layer below. By the fourth layer, your planter should be 16 inches tall. Check that the box is square and all boards are flush.

48-inch cedar boards46.5-inch cedar boardscordless drill2.5-inch exterior screwssquare

Add drainage holes to the bottom

Flip the entire box upside down (or work from underneath if already in place). Using a spade bit or large drill bit, drill 6-8 drainage holes evenly spaced across the bottom. These holes (about 1/2 to 3/4 inch diameter) prevent water from pooling and rotting plant roots.

cordless drillspade bit or large drill bit

Position the planter in its final location

With help if needed, move the planter box to your chosen garden spot. Make sure it's level—use shims or adjust the ground beneath if necessary. Cedar is heavy when filled with soil, so this is your last chance to reposition easily.

planter boxlevelshims (optional)

Line the bottom with landscape fabric

Cut a piece of landscape fabric slightly larger than the planter's footprint. Lay it inside the bottom of the box, letting excess drape up the sides slightly. This prevents soil loss through drainage holes while still allowing water to escape. Staple it to the inside walls if desired.

landscape fabricscissorsstaple gun (optional)

Fill with soil and plant

Fill your planter with high-quality garden soil or a mix of topsoil, compost, and peat moss. Fill to about 1-2 inches below the rim. Water the soil lightly to settle it, add more if needed, then plant your vegetables, herbs, or flowers. Your cedar planter is now ready to grow!

garden soilcompostplantswater