Build a Simple Wooden Side Table
Woodworking

Build a Simple Wooden Side Table

Create a sturdy, classic side table perfect for any room in your home. This beginner-friendly woodworking project takes about 4-6 hours and requires basic tools. Great for anyone looking to build their first piece of furniture with clean, timeless design.

AM
Alex M.· Nov 11, 2026
0 of 17 done

Plan your dimensions and gather materials

Decide on your final table size. This guide uses 18 inches wide × 18 inches deep × 24 inches tall. Gather all your wood boards and lay them out in your workspace. Check each piece for warping or damage before starting.

measuring tapepencilworkspace

Cut the tabletop boards

Measure and mark four 18-inch lengths from your 1×6 pine boards for the tabletop. Use a miter saw or circular saw to make clean, square cuts. Sand the cut ends smooth with 120-grit sandpaper.

miter sawmeasuring tapepencil120-grit sandpapersafety glasses

Cut the table legs

Measure and cut four 24-inch pieces from 2×2 boards for the legs. Make sure all four legs are exactly the same length so your table sits level. Sand any rough edges.

miter sawmeasuring tape2×2 pine boards120-grit sandpaper

Cut the apron pieces

Cut four pieces from 1×4 boards: two at 18 inches (for front and back) and two at 16 inches (for the sides, accounting for the thickness of the front/back pieces). These apron pieces connect the legs and support the tabletop.

miter sawmeasuring tape1×4 pine boardspencil

Sand all pieces thoroughly

Sand every piece of wood with 120-grit sandpaper, then finish with 220-grit for a smooth surface. Pay special attention to edges and ends. Wipe away all sawdust with a tack cloth or damp rag.

120-grit sandpaper220-grit sandpapertack clothsanding block

Assemble the first leg and apron connection

Take one leg and one 18-inch apron piece. Apply wood glue to the top end of the leg, position the apron flush with the top, and clamp together. Pre-drill two pilot holes through the apron into the leg, then drive in 2.5-inch wood screws. The apron should sit about ½ inch down from the very top of the leg.

wood glueclampsdrill2.5-inch wood screwspilot bit

Attach the second leg to the same apron

Apply glue to the top of another leg and attach it to the opposite end of the same 18-inch apron piece. Clamp, pre-drill, and screw just like the first leg. You now have two legs connected by one apron piece.

wood glueclampsdrill2.5-inch wood screws

Build the second leg pair

Repeat steps 6 and 7 with the remaining two legs and the other 18-inch apron piece. You should now have two identical assemblies, each with two legs connected by an apron.

wood glueclampsdrill2.5-inch wood screws

Connect the two assemblies with side aprons

Stand both leg assemblies upright. Take one 16-inch apron piece and attach it between the two assemblies on one side. Apply glue, clamp, pre-drill, and screw into each leg. Make sure everything is square by measuring diagonally across the frame—both diagonal measurements should be equal.

wood glueclampsdrill2.5-inch wood screwsmeasuring tapesquare

Attach the final side apron

Attach the last 16-inch apron piece to complete the rectangular base frame. Double-check that all corners are square and the table sits flat on your work surface. Let the glue dry for at least 30 minutes.

wood glueclampsdrill2.5-inch wood screwssquare

Prepare the tabletop

Lay your four 18-inch 1×6 boards side by side, creating an 18×18 inch square top. Arrange them with the best-looking grain facing up. Mark the underside so you know which side is which.

1×6 pine boardspencil

Attach support cleats to the tabletop

Cut two 12-inch pieces from scrap 1×2 or 1×3 wood for cleats. Place these across the underside of the tabletop, about 3 inches from each end, perpendicular to the boards. Apply glue and screw through the cleats into each tabletop board with 1.25-inch screws. These hold the top together.

1×2 boardswood gluedrill1.25-inch wood screwsmeasuring tape

Attach the tabletop to the base

Flip your table base upside down. Center the tabletop (also upside down) on top of the leg frame. The tabletop should overhang evenly on all sides. Drive 1.5-inch screws up through the apron pieces into the underside of the tabletop—2-3 screws per apron piece.

drill1.5-inch wood screwsmeasuring tape

Fill holes and imperfections

Use wood filler to fill any screw holes on visible surfaces, gaps, or imperfections. Let dry completely (follow product directions), then sand smooth with 220-grit sandpaper. Wipe away all dust.

wood fillerputty knife220-grit sandpapertack cloth

Apply stain or paint

Flip your table right-side up. Apply your chosen stain or paint with a brush or cloth, following the wood grain. Work in a well-ventilated area. Apply multiple thin coats as needed, allowing drying time between coats. For stain, wipe off excess after a few minutes.

wood stain or paintpaintbrush or clothdrop clothgloves

Apply protective finish

Once stain or paint is completely dry, apply 2-3 coats of polyurethane or clear sealer for protection. Use light, even strokes and allow each coat to dry fully. Lightly sand between coats with 220-grit sandpaper for a smooth finish.

polyurethanepaintbrush220-grit sandpapertack cloth

Final inspection and touch-ups

After the final coat is completely dry (wait 24-48 hours), inspect your table. Touch up any missed spots or rough areas. Check that the table sits level and all joints are secure. Your side table is ready to use!

clean clothlevel
Build a Simple Wooden Side Table — Howdy