Build a Wall-Mounted Wooden Spice Rack
Woodworking

Build a Wall-Mounted Wooden Spice Rack

Create a sturdy and attractive wall-mounted spice rack to organize your kitchen spices. This beginner-friendly woodworking project takes about 3-4 hours and requires basic tools. Perfect for anyone looking to add custom storage and charm to their kitchen.

AM
Alex M.· Oct 25, 2026
0 of 20 done

Plan your design and take measurements

Decide how many shelves you want (2-3 is typical) and measure the wall space where you'll mount the rack. Standard spice jars are about 2 inches wide and 4 inches tall, so plan shelf depth at 3 inches and spacing at 5 inches between shelves.

tape measurepencilpaper

Cut the back panel

Using your measurements, cut the back panel from your 1x6 pine board. A common size is 18 inches wide by 16 inches tall. Mark your cut line clearly with a pencil and carpenter's square, then cut with a hand saw or circular saw.

1x6 pine boardtape measurepencilcarpenter's squarehand saw or circular saw

Cut the shelf pieces

From your 1x3 pine board, cut 2-3 shelves to match the width of your back panel (18 inches if following the standard size). These will hold your spice jars, so make sure all cuts are straight and even.

1x3 pine boardtape measurepencilcarpenter's squarehand saw or circular saw

Cut the side supports

Cut two side pieces from your 1x3 board to the full height of your back panel (16 inches). These will provide extra support and a finished look to the sides of your rack.

1x3 pine boardtape measurepencilhand saw or circular saw

Sand all wood pieces

Thoroughly sand all cut pieces starting with 120-grit sandpaper to remove rough edges and splinters, then finish with 220-grit for a smooth surface. Sand with the grain of the wood and pay special attention to edges and cut ends.

120-grit sandpaper220-grit sandpapersanding block

Mark shelf positions on back panel

Lay the back panel face-up and use your pencil and carpenter's square to mark where each shelf will attach. Space shelves evenly (typically 5 inches apart) and draw light horizontal lines across the back panel at each position.

pencilcarpenter's squaretape measure

Apply wood glue to first shelf

Apply a thin, even bead of wood glue along the back edge of your first shelf piece. Position it carefully on the lowest marked line on the back panel, making sure it's perfectly aligned with your pencil mark.

wood glue

Attach first shelf with screws

Pre-drill pilot holes through the back panel into the shelf edge using a drill bit slightly smaller than your screws. Drive 3-4 evenly spaced 1.25-inch wood screws through the back into the shelf. Wipe away any excess glue immediately.

electric drilldrill bits1.25-inch wood screwsscrewdriver bitdamp cloth

Attach remaining shelves

Repeat the gluing and screwing process for each remaining shelf, working from bottom to top. Make sure each shelf is level and properly aligned before drilling. Allow glue to dry for at least 30 minutes between shelves for best results.

wood glueelectric drill1.25-inch wood screwslevel

Attach side support pieces

Apply wood glue to the back edge of each side support piece and position them flush against the sides of the back panel. Pre-drill and attach with 1.25-inch wood screws every 4-5 inches along the length, making sure they're perfectly vertical.

wood glueelectric drill1.25-inch wood screwslevel

Add front lip to shelves

Cut thin strips (about 0.5 inches wide) from scrap wood to create a small lip on the front edge of each shelf to prevent jars from sliding off. Glue and nail or screw these in place along the front edge of each shelf.

scrap woodhand sawwood gluesmall finishing nails or screwshammer or drill

Fill screw holes and imperfections

Use wood filler to fill all visible screw holes, gaps, and any imperfections in the wood. Apply with a putty knife, overfill slightly, and let dry completely according to package directions (usually 30-60 minutes).

wood fillerputty knife

Sand the filled areas smooth

Once the wood filler is completely dry, sand all filled areas smooth with 220-grit sandpaper until they're flush with the surrounding wood surface. Wipe away all dust with a clean, dry cloth.

220-grit sandpaperclean cloth

Apply stain or paint

Apply your choice of wood stain or paint using a brush or cloth, following the product directions. Work with the grain for stain. Apply thin, even coats and allow to dry completely between coats. Two coats usually provide the best coverage and color.

wood stain or paintpaintbrush or staining clothstirring stick

Apply protective finish

Once stain or paint is completely dry, apply a clear protective finish like polyurethane or furniture wax. This protects the wood from moisture and kitchen grease. Apply with a clean brush in thin, even coats and let dry per product instructions.

polyurethane or furniture waxclean paintbrushlint-free cloth

Attach mounting hardware to back panel

Flip the rack over and attach D-ring hangers or keyhole hangers to the back panel, positioning them about 3-4 inches from the top edge and evenly spaced from the sides. Pre-drill small pilot holes and screw them in securely.

2 D-ring hangers or keyhole hangerselectric drillsmall screwstape measure

Mark wall mounting position

Hold the rack against your wall where you want it mounted and use a level to make sure it's straight. Lightly mark the wall through the mounting hardware with a pencil to indicate where you'll need to drill.

levelpencil

Install wall anchors

If mounting into drywall (not into studs), drill holes at your marked positions and tap wall anchors into place with a hammer. If you're fortunate enough to mount into wall studs, you can skip the anchors and drill pilot holes directly.

electric drillappropriate drill bitwall anchorshammerstud finder

Mount the spice rack to wall

With help if needed, lift the rack into position and align the mounting hardware with your wall anchors or pilot holes. Drive screws through the mounting hardware into the wall anchors or studs until the rack is firmly secured. Check that it's level one final time.

2-inch wall screwselectric drill or screwdriverlevel

Fill with spices and enjoy

Arrange your spice jars on the shelves, placing the ones you use most frequently at eye level for easy access. Step back and admire your custom woodworking project. Your kitchen is now more organized and stylish!

spice jars