Build a Wooden Wall-Mounted Spice Rack
Woodworking

Build a Wooden Wall-Mounted Spice Rack

Create a custom wooden spice rack that mounts to your kitchen wall and holds 12-15 standard spice jars. This beginner-friendly woodworking project takes about 3-4 hours and requires basic tools. Perfect for organizing your cooking space and adding a rustic touch to your kitchen.

AM
Alex M.· Nov 20, 2026
0 of 14 done

Plan your design and measurements

Measure your spice jars to determine the depth needed for your shelves (typically 3-4 inches). Decide on the overall dimensions — a rack that's 24 inches wide by 18 inches tall with 3 shelves works well for most kitchens. Sketch your design on paper, marking where each shelf will go and how you'll attach it to the wall.

measuring tapepencilpaper

Cut the back panel

Using a circular saw or hand saw, cut your pine board to create the back panel. For a standard design, cut it to 24 inches wide by 18 inches tall. Sand the edges smooth with 120-grit sandpaper to remove any splinters or rough spots.

1x8 pine boardcircular saw120-grit sandpaper

Cut the shelf pieces

Cut three shelf pieces from your pine board, each 24 inches long and 3.5 inches deep. These will hold your spice jars. Cut six small side pieces (3.5 inches long by 1 inch tall) to act as lips on each shelf to prevent jars from sliding off. Sand all pieces smooth.

1x4 pine boardcircular saw120-grit sandpaper

Mark shelf placement on back panel

Lay your back panel flat. Using a pencil and ruler, mark horizontal lines where each shelf will attach. Space them evenly — about 5 inches apart works well. Mark at 4 inches from the bottom, 9 inches from the bottom, and 14 inches from the bottom for three shelves.

pencilrulerback panel

Attach the front lips to shelves

Take each shelf piece and attach a small lip piece to the front edge using wood glue and 1-inch finishing nails. The lip should sit flush with the top of the shelf to create a small barrier. Hold each in place for 30 seconds while the glue sets, then secure with 2-3 nails per lip. Let dry for 15 minutes.

wood glue1-inch finishing nailshammershelf pieceslip pieces

Pre-drill holes for shelf attachment

To prevent wood splitting, use a drill with a 1/16-inch bit to pre-drill two holes through the back panel at each shelf marking line. Space the holes about 2 inches from each edge. These holes will guide your screws when attaching the shelves.

power drill1/16-inch drill bitback panel

Attach shelves to back panel

Apply wood glue along the back edge of each shelf. Position each shelf on its marked line on the back panel. Using your power drill, drive 1.5-inch wood screws through the pre-drilled holes from the back into the shelf edge. Attach all three shelves, making sure they're level. Wipe away any excess glue with a damp cloth.

wood glue1.5-inch wood screwspower drilldamp clothshelves

Sand the entire assembly

Once the glue has dried (wait at least 30 minutes), sand the entire rack with 120-grit sandpaper, then finish with 220-grit for a smooth surface. Pay special attention to edges and any areas where wood pieces meet. Wipe away all dust with a tack cloth or damp rag.

120-grit sandpaper220-grit sandpapertack cloth

Apply wood stain or paint

Using a brush or cloth, apply your chosen wood stain or paint in even strokes, following the wood grain. Work in a well-ventilated area. Apply a thin, even coat and let it dry for 2-4 hours according to the product instructions. Apply a second coat if you want a deeper color, letting it dry completely.

wood stain or paintpaintbrushclean cloth

Apply protective finish

Once the stain or paint is completely dry, apply a clear polyurethane or sealer to protect the wood from moisture and kitchen grease. Use a clean brush to apply a thin, even coat. Let dry for 4-6 hours or overnight for best results. This makes the rack easier to clean.

polyurethane sealerclean paintbrush

Install wall mounting hardware

Flip the rack over so the back faces you. Measure and mark two points about 16 inches apart (to hit wall studs if possible) and 2 inches from the top edge. Attach two D-ring hangers or keyhole hangers using the provided screws. Make sure they're level with each other so your rack hangs straight.

D-ring hangersscrewdrivermeasuring tapepencil

Find wall studs and mark mounting points

Use a stud finder to locate wall studs in your chosen kitchen location. Mark the stud locations with pencil. Hold your spice rack against the wall at the desired height and mark through the mounting hardware onto the wall. If studs don't align with your hardware, you'll need to use wall anchors instead.

stud finderpencillevel

Mount the rack to the wall

Drill pilot holes at your marked points on the wall. If mounting to studs, use 2.5-inch wood screws driven directly into the studs. If using drywall, install wall anchors first, then screw into the anchors. Hang your spice rack on the screws or anchors, making sure it's level and secure before loading it with jars.

power drill2.5-inch wood screwswall anchorslevel

Load and arrange your spices

Once the rack is securely mounted, arrange your spice jars on the shelves. Place taller jars on the bottom shelf and shorter ones on top shelves for easy visibility. The front lip on each shelf will keep jars from sliding off. Step back and enjoy your new organized spice storage!

spice jars
Build a Wooden Wall-Mounted Spice Rack — Howdy