DIY Wooden Phone Stand from Scrap Wood
Woodworking

DIY Wooden Phone Stand from Scrap Wood

Build a simple, functional phone stand using scrap wood pieces in about 1-2 hours. Perfect for beginners with basic woodworking tools, this project turns leftover wood into a practical desk accessory that holds your phone at a comfortable viewing angle.

AM
Alex M.· Nov 18, 2026
0 of 17 done

Gather and inspect your scrap wood

Look through your scrap wood pile for suitable pieces. You'll need one piece approximately 6 inches long and 3-4 inches wide for the base, and another piece about 4-5 inches long for the upright support. Check that the wood is free from major cracks or rot.

scrap wood piecesmeasuring tape

Design your stand dimensions

Sketch a simple design on paper. The base should be stable (around 6" x 3-4"), and the upright should lean back at about 60-70 degrees to hold your phone comfortably. Decide if you want a slot cut into the upright or just a leaning surface.

pencilpaperruler

Mark the base piece

Using your pencil and ruler, mark where the upright will attach to the base. This is typically about 1-1.5 inches from the back edge, centered on the width. Draw clear lines so you know where to position everything.

pencilrulersquare

Cut the base to size

If your scrap wood isn't already the right size, use a handsaw or miter saw to cut the base piece to approximately 6 inches long and 3-4 inches wide. Sand the edges smooth after cutting to remove splinters.

handsaw or miter sawsandpaper 120-grit

Cut the upright support

Cut your upright piece to 4-5 inches in height and about 2-3 inches wide. This piece will hold your phone, so make sure it's tall enough for your device. Sand any rough edges smooth.

handsaw or miter sawsandpaper 120-grit

Cut the angle on the upright (optional but recommended)

To create a better viewing angle, cut the bottom of the upright at a 20-30 degree angle so it leans back naturally when attached to the base. Mark the angle with a pencil and use a miter saw or hand saw carefully.

miter saw or handsawprotractor or angle finderpencil

Create the phone slot (optional)

If you want a slot to hold the phone's bottom edge, mark a groove about 1/4 inch deep and 1/2 inch from the bottom of the upright. Use a router, table saw with multiple passes, or carefully chisel out this slot. This keeps the phone from sliding.

router or chiselclampspencil

Sand all pieces thoroughly

Using 120-grit sandpaper, sand all surfaces and edges of both pieces until smooth. Pay extra attention to edges and corners where you'll handle the stand. Finish with 220-grit sandpaper for a silky feel.

sandpaper 120-gritsandpaper 220-gritsanding block

Mark drill pilot holes

Position the upright on the base where you marked earlier. Use a pencil to mark through the upright into the base where you'll drill pilot holes. Two screws are usually sufficient for stability.

pencilclampssquare

Drill pilot holes

Using a drill bit slightly smaller than your screws, drill pilot holes through the marks on the upright and into the base. This prevents the wood from splitting when you drive the screws in.

drilldrill bit setclamps

Apply wood glue

Apply a thin, even layer of wood glue to the bottom surface of the upright where it will contact the base. Don't use too much or it will squeeze out messily.

wood gluesmall brush or spreader

Attach the upright to the base

Position the upright on the base, aligning with your marks and pilot holes. Drive 1.5-2 inch wood screws through the pilot holes to secure the pieces together. Make sure the upright is perpendicular to the base (or at your desired angle).

1.5-2 inch wood screwsscrewdriver or drill with driver bitclamps

Wipe away excess glue

While the glue is still wet, use a damp cloth to wipe away any glue that squeezed out from the joint. This is much easier now than sanding it off later.

damp cloth

Let the glue cure

Allow the wood glue to dry completely according to the manufacturer's instructions, typically 30 minutes to 1 hour for handling, and 24 hours for full strength. Don't apply finish or use the stand until dry.

patience

Apply finish (optional)

Once dry, you can apply a finish like mineral oil, wood stain, polyurethane, or leave it natural. Apply with a brush or cloth following the product instructions. This protects the wood and enhances its appearance.

wood finish of choicebrush or clothdrop cloth

Add non-slip pads to the base

Attach small felt pads or rubber bumpers to the bottom four corners of the base. This prevents the stand from sliding on your desk and protects your surface from scratches.

felt pads or rubber bumpersscissors if needed

Test your phone stand

Place your phone in the stand to test the angle and stability. Make sure it holds your phone securely at a comfortable viewing angle. If needed, you can adjust the angle by sanding the bottom of the upright slightly.

phone