Small Wooden Side Table
Woodworking

Small Wooden Side Table

Build a sturdy and stylish small side table perfect for a living room or bedroom. This beginner-friendly woodworking project takes about 4-6 hours over a weekend and requires basic tools. Great for anyone looking to add a custom piece of furniture to their home!

AM
Alex M.· Nov 19, 2026
0 of 13 done

Plan your table dimensions

Decide on your final table size. A typical small side table is 18 inches wide, 18 inches deep, and 24 inches tall. Sketch your design on paper, noting the tabletop size and leg placement. This helps you visualize the finished piece before cutting any wood.

pencilpapertape measure

Cut the tabletop boards

Measure and mark your pine boards to create an 18x18 inch tabletop. You'll need to cut 3-4 boards (depending on width) to the same 18-inch length. Use a miter saw or circular saw with a straight edge guide for clean, square cuts. Sand the cut edges smooth with 120-grit sandpaper.

pine boards 1x6miter sawtape measurepencil120-grit sandpaper

Arrange and join the tabletop

Lay your cut boards side by side on a flat surface to form the 18x18 inch top. Apply wood glue along the edges where boards meet, then clamp them together tightly. Use at least 3 bar clamps to hold everything in place. Wipe away excess glue with a damp cloth and let dry for at least 2 hours.

wood gluebar clampsdamp cloth

Cut the table legs

Measure and cut four table legs from your 2x2 lumber, each 23 inches long (accounting for the 3/4-inch thick tabletop to reach 24 inches total height). Make sure all four legs are exactly the same length so your table sits level. Sand the cut ends smooth.

2x2 lumbermiter sawtape measurepencil120-grit sandpaper

Cut the apron pieces

The apron connects the legs and provides structural support. Cut four pieces from 1x3 lumber: two at 16 inches (for the sides between legs) and two at 16 inches (for front and back). These will sit inside the legs, creating a frame. Sand all pieces smooth.

1x3 lumbermiter sawtape measurepencil120-grit sandpaper

Assemble the leg and apron frame

Lay one leg flat on your work surface. Position an apron piece flush with the top of the leg and 3/4 inch inset from the outer edge. Pre-drill two pilot holes through the leg into the apron end to prevent splitting. Drive 2.5-inch wood screws to attach. Repeat for all four corners, creating a rectangular frame with legs at each corner.

drillpilot bit2.5-inch wood screwsscrewdriver bit

Square and secure the base frame

Stand the leg frame upright and check that it's square by measuring diagonally from corner to corner—both measurements should be equal. Adjust if needed, then add corner braces or additional screws where the apron pieces meet the legs for extra stability. This creates a rock-solid base.

tape measurecorner braces1-inch screws

Sand the entire frame

With the base assembled, sand all surfaces of the legs and apron with 120-grit sandpaper, then follow up with 220-grit for a smooth finish. Pay special attention to corners and edges where someone might touch the table. Remove all sawdust with a clean cloth or tack cloth.

120-grit sandpaper220-grit sandpapertack cloth

Attach the tabletop to the base

Place your dried and glued tabletop face-down on a protected surface. Center the leg frame upside-down on the underside of the tabletop. Pre-drill pilot holes from inside the apron up into the tabletop (don't drill through the top!). Attach with 1.5-inch wood screws, using 2 screws per side of the apron.

drillpilot bit1.5-inch wood screwsscrewdriver bit

Final sanding of the tabletop

Flip the table right-side up. Sand the entire tabletop surface with 120-grit sandpaper, moving with the wood grain. Follow with 150-grit, then finish with 220-grit for a silky-smooth surface. Sand the edges and corners gently to remove sharp edges. Clean off all dust thoroughly.

120-grit sandpaper150-grit sandpaper220-grit sandpapertack cloth

Apply wood stain (optional)

If you want to add color, apply wood stain with a brush or cloth, working in the direction of the grain. Start with the legs and apron, then do the tabletop last. Let the stain sit for 5-10 minutes, then wipe off excess with a clean cloth. Allow to dry completely according to the stain manufacturer's instructions (usually 4-8 hours).

wood stainbrush or staining clothclean rags

Apply protective finish

Once stain is dry (or on bare wood if you skipped staining), apply a protective polyurethane finish. Use a clean brush to apply a thin, even coat over all surfaces. Let dry for 4 hours, then lightly sand with 220-grit sandpaper. Apply a second coat and let dry overnight.

polyurethanepaintbrush220-grit sandpaper

Add felt pads and final touches

Once the finish is fully cured (24 hours), flip the table over and attach self-adhesive felt pads to the bottom of each leg. This protects your floors from scratches. Inspect the table for any rough spots and do touch-up sanding if needed. Your side table is now complete!

felt pads220-grit sandpaper